🎄Smart Differential Receivers and F16V3 Firmware Upgrade (2019)🎄

Taking a quick look at the new Smart (chain-able) differential deceivers. Also go through a Falcon F16V3 firmware upgrade to support the new boards.

9 thoughts on “🎄Smart Differential Receivers and F16V3 Firmware Upgrade (2019)🎄

  1. David Laro

    Hi Jeff.
    I have a f16v3 (updated) and 3 smart receiver boards and a differential expansion board (not using it after seeing you recent video) I’m trying to use the receivers on a 1600 pixel 360 degree mega tree with a 90 pixel star on top. I have the tree wired in 8 sets of 200 in xlights configuration in the layout page, all the ports on the 2 receiver boards are used and 1 port on the third is for the star. in color wash they all work great. however i’m not sure how to configure them in xlights since all ports are taken up on boards A and B , but in xlights the tree prop is configured in 8 strings @200 nodes per string @4strands per string and the only give you a single port to assign in the smart receiver portion of the controller connection section of the layout page David pitts says I can run 200 pixels per port on the boards daisy chained with power injection which is how its wired now. Any ideas how to fix this? I’m Stuck and not sure what to do. is there a setting in the f16 i’m missing or overlooked? Thanxs Jeff.

  2. Don Shoaff

    I saw the whole show. The patriotic part was a blast. My wife would have loved it. She had me do our house with a lot of red white and blue, a task that would have been much easier had I used rgb pixels instead of ac lights. Every sequence fit the songs very well. My favorite was the For King and Country song. Having seen their live show a few times I can say your sequencing fit them very well. I hope to have reason to visit Austin and your show next year.

  3. Dog Father Post author

    Don, Glad you enjoyed it! Little Drummer Boy is a downloadable sequence for xLights Around the World this year. Jeff

  4. David Laro

    Yes the star is a separate prop that is allocated to board C port 1. Boards A and B are ver. 1.02 and C is 1.01 which Davis Pitts sent me a terminator plug for board C if that that matters. Not sure how to assign each port of boards A and B in xlights for the 8 strings if 200 so i can save that configuration to my f16v3 like you did in your video. The board dip switches are set correctly. Im guessing with the terminator plug David sent me for board c terminates it and thinking both sets of terminator dip switches will also need to be turned on. the pixels themselves light up in white from the connection point up to about 15 then the top pixel of those 15 notes are lit up either green or red this happens when no data is being sent to the reciever boards. All 4 data led on the reciever boards light up when powered up

  5. Dog Father Post author

    I’ll admit that I don’t know all the differences between the different versions of this board, but I’d guess the terminator he sent is if you use on of the 1.01 boards at the end of a chain. With the 1.02 board, you can use it’s on-board terminator (guessing). Using both on “C” doesn’t sound right. As for the xLights config, again, not sure, but I would try setting the tree as the “A” board and the star as the “C” board and see if xLights figures out “B’s” settings based on the other model settings. You can check the Falcon config after you program it from xLights. I am using a DR on a matrix and when powered on, I have several lights at the beginning of the string that light up white, but they go off after about 10 seconds once the controller is fully initialized.

  6. David Laro

    So xlights sent the star layout to board c to the f16v3 and split the strings ports page on the controller to the 3 SR boards. However it did not send the tree string parameters to boards A and B. I was hoping it would do an overflow effect. As soon as 200 filled up the first port it would fill next port and so on. Not the case and still stumped. shoot me an email to where i can send you screen shots of my layout set up, and hopefully you might see something that’s out of place that im missing.

  7. Dog Father Post author

    You might try logging into the xLights Zoom room (see xlights.org). You can share your screen and interact live with people smarter than me. πŸ™‚ I really have no other options to try at this point since I haven’t tried to span a prop across multiple boards.

  8. David Laro

    Ok I’ll give zoom a try, i might give David Pitts a call also, and see if there’s something im missing. Thanks again for helping Jeff!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.